>   제품   >  고급검색

Tris(2,4-pentanedionato)iron(III)
(CAS RN:14024-18-1 제품번호:I0079)

구조식

Tris(2,4-pentanedionato)iron(III)
동의어의 Acetylacetone Iron(III) Salt
동의어의 Ferric(III) Acetylacetonate
동의어의 Iron(III) Acetylacetonate

일반 정보

제품번호 I0079

•본 제품의 재고는 일본 본사의 재고입니다. 주문시, 5일안에 실험실까지 도착됩니다.
•본건의 원가격은 한국 대리점의 예상 판매가격입니다.
자세한 정보가 필요하시면 연락해 주십시오.
(세진시아이 (한국총대리점) 전화 : 02-2655-2480 이메일 : sales@sejinci.co.kr)
•킬로그램~톤 단위로 필요한 경우, 「대량 구매 및 견적의뢰」를 클릭하여, 전용의뢰서로 문의해 주시기 바랍니다. 일부 제품에 한하여 희망에 응하지 못하는 경우가 있으므로 미리 양해해 주시기 바랍니다.
•저희 회사는 보관 조건을 최적화하기 위해 항상 검토 중입니다. 제품의 최신 보관 온도는 홈페이지에 기재된 내용임을 알려드립니다.

순도/분석 방법 >98.0%(T)
보관 온도
M.F. / M.W. C15H21FeO6=353.17
CAS RN 14024-18-1
관련 CAS RN
MDL 번호 MFCD00000020
용기
  • 제품 정보
  • 안전 및 규정
  • 참조

규격

Purity(Chelometric Titration) min. 98.0 %
Solubility in Toluene almost transparency

참조

PubChem SID 87571482
F&F 6,304
RTECS# NO8960000

GHS

픽토그램
신호 워드 Warning
위험물 및 유해 등록
  • H302
  • :Harmful if swallowed.
  • H315
  • :Causes skin irritation.
  • H319
  • :Causes serious eye irritation.
주의 사항
  • P264
  • :Wash hands and face thoroughly after handling.
  • P270
  • :Do not eat, drink or smoke when using this product.
  • P280
  • :Wear protective gloves, eye protection.
  • P301+P312+P330
  • :If swallowed: Call a poison center or doctor if you feel unwell. Rinse mouth.
  • P302+P352+P332+P313+P362+P364
  • :If on skin: Wash with plenty of soap and water. If skin irritation occurs: Get medical advice or attention. Take off contaminated clothing and wash it before reuse.
  • P305+P351+P338+P337+P313
  • :If in eyes: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical advice or attention.
  • P501
  • :Dispose of contents and container in accordance with local, regional, national regulations (e.g. US: 40 CFR Part 261, EU:91/156/EEC, JP: Waste Disposal and Cleaning Act, etc.).

이용 예

2-PySO2CF2H : Bench-stable Difluoromethylating Agent for Catalytic Difluoromethylation

D5390, I0079

References

Iron/dppbz-catalyzed Decarboxylative Couplings of Active Esters

I0079

In a screwed-capped vial active ester (0.1 mmol), Fe(acac)3 (0.005 – 0.04 mmol) and dppbz (0.006 – 0.048 mmol) are weighed. The vial is then sealed, evacuated and back-filled with Ar. Then, 0.5 mL of distilled THF is added. The mixture is stirred for 5 minutes under Ar and diarylzinc reagent in THF (ca. 0.3 mol/L, 0.15 – 0.25 mmol) is added in one portion at 0 - 25 ºC to the mixture and stirred at the same temperature for 1 h. After this time, the reaction is quenched with 1 mol/L HClaq, sat. NH4Claq or H2O and diluted with diethyl ether. The organic layer is separated and dried over Na2SO4 anhydrous, filtered and evaporated to dryness. Pure products are obtained after column chromatography or preparative TLC.

References

Iron-Catalyzed ortho-Alkylation of Carboxamides

I0079

Typical procedure (R = benzyl): To Fe(acac)3 (17.1 mg, 0.05 mmol), dppe (29.9 mg, 0.075 mmol), and 3-methyl-N-(quinolin-8-yl)benzamide (131 mg, 0.5 mmol) are added THF (4 mL), and benzyl chloride (190 mg, 1.5 mmol). The mixture is then placed in an oil bath at 65 °C and PhMgBr (16% in THF, ca. 1 mol/L) (0.6 mL, 0.6 mmol) is added in a single portion. Upon completion of PhMgBr addition, the reaction mixture is stirred at 65 °C for 1 min. Then PhMgBr (16% in THF, ca. 1 mol/L) (1.3 mL, 1.3 mmol) is added dropwise at 65 °C for 9 min. The reaction mixture is stirred at 65 °C for 1 min and brought to rt. Subsequently the reaction mixture is quenched with a saturated solution of ammonium chloride (535 mg, 0.01 mol) and extracted with dichloromethane (3 x 3 mL). The combined organic extracts are dried over MgSO4, filtered and concentrated to give a residue. The residue is purified by silica gel flash chromatography (eluent: hexanes/EtOAc = 20:1) to give 2-benzyl-5-methyl-N-(quinolin-8-yl)benzamide (175 mg, 99% yield) as a white solid.

References

Efficient Fe/Cu Co-Catalyzed C-N Cross-Coupling Reaction

Typical procedure (Entry 1): A Schlenk tube is charged with p-anisidine (92.4 mg), K2CO3 (138 mg), Fe(acac)3 (34.4 mg), and Cu(OAc)2• H2O (20 mg). Under a nitrogen atmosphere, 4-bromotoluene (85.5 mg) is added followed by dry DMF (0.8 mL). The reaction mixture is then heated to 135 ºC, and stirred for 20 h. The mixture is cooled to room temperature and diluted with diethyl ether. The resulting suspension is filtered through a celite pad and the filtrate is concentrated. The residue is purified by column chromatography on silica gel (eluent: petroleum ether/ethyl acetate) to give 4-methoxy-N-p-tolylaniline (98.1 mg, 92 %).

References

Iron-Catalyzed Cross-Coupling Reaction

References

페이지 맨 위로