Silver Stain Kit [for Electrophoresis]

×

순도/분석 방법:

동의어의:

제품문서:

SDS | 규격표 | 시험성적서， 각종 증명서 | 분석 차트

일반 정보 | 규격치/물성치 | 안전 및 규정 | 이용 예・문헌

제품보충정보

이 페이지에 대한 설명

포장단위	가격	당일출고	2-3일 이내 출고	추가로 필요한 경우	출하 정보
1KIT	₩299,300	10	0	문의	출하 시뮬레이션

•본 제품의 재고는 일본 본사의 재고입니다. 주문시, 5일안에 실험실까지 도착됩니다.
•본건의 원가격은 한국 대리점의 예상 판매가격입니다.자세한 정보가 필요하시면 연락해 주십시오.( SEJIN CI Co., Ltd. (한국총대리점) 전화 : 02-2655-2480 이메일 :  sales@sejinci.co.kr)
•보관 조건은 예고없이 변경 될 수 있습니다. 제품 보관 조건의 최신 자료는 홈페이지에 기재되어 있으니 양해 부탁드립니다.

대량 구매 및 견적의뢰

Product Information

• Components : Solution-1 (Enhancing solution) 50 mL, Solution-2 (Staining solution) 50 mL, Solution-3 (Developer solution #1) 50 mL, Solution-4 (Developer solution #2) 50 mL
• Size : 50 tests (90 mm x 80 mm, 1 mm gel)

Description

• Silver staining is a highly-sensitive and rapid detection method for SDS-PAGE separated proteins or nucleic acids. It is several times more sensitive than the commonly used EtBr or CBB staining methods.

Direction for Use

[Solution Preparation]

• Agitate each included solution well, and prepare the following 4 solutions in advance.
  The volumes of reagents given below is based on a gel size of 90 mm x 80 mm x 1 mm. For different sizes of gel, the volume of reagents should be adjusted accordingly. For methanol and acetic acid, it is recommended to use special grade or any other higher grade.
• Fixing Solution : Deionized water : 40 mL + Methanol : 50 mL + Acetic acid : 10 mL + Solution-1 (Enhancing solution) : 1 mL
• Staining Solution : Deionized water : 100 mL + Solution-2 (Staining solution) : 1 mL
• Developer Solution : Deionized water : 200 mL + Solution-3 (Developer solution #1) : 1 mL + Solution-4 (Developer solution #2) : 1 mL
• Stop Solution : Deionized water : 100 mL + Acetic acid : 1 mL

[Usage]

1. Soak the gel in 100 mL of Fixing Solution in a clean tray and incubate it with shaking for 10 minutes.
2. Remove the solution from step 1, and wash gel with 100 mL of deionized water with shaking for 10 minutes.
   (Repeat a total of three times)
3. Remove the solution from step 2, and add 100 mL of Staining Solution. Allow to incubate with shaking for 5 minutes.
   *When disposing of Solution-2 (i.e. Staining Solution), add hydrochloric acid or sodium chloride to the container to precipitate out silver chloride.
4. Remove the solution from step 3, and add 100 mL of deionized water. Incubate with shaking for 30 seconds.
5. Remove the solution from step 4, and add 100 mL of Developer Solution. Incubate with shaking for 30 seconds.
6. Remove the solution from step 5, and add 100 mL of Developer Solution. Allow to incubate with shaking until developed bands appear.
   *Developing time will vary by sample, temperature, and thickness of gel, so adjust accordingly.
   *A 90 mm x 80 mm x 1 mm gel will take approximately 5-10 minutes.
7. Remove the solution from step 6, and add 100 mL of Stop Solution. Incubate with shaking for 10 minutes.
8. Remove the solution from step 7, and wash with 100 mL of deionized water, incubating with shaking for 5 minutes between washes. (Repeat a total of three times.)

Storage

• Store at 4 ºC. This product is photosensitive and should be protected from light. Use within 1 year.