text.skipToContent text.skipToNavigation

Maximum quantity allowed is 999

Please select the quantity
Organic Transistor > Organic Transistor (OFET) Device Fabrication and Evaluation >

Fabrication and Evaluation of Organic Field-Effect Transistors (OFETs) : P3HT

P3HT [P2513]

Poly(3-hexylthiophene-2,5-diyl) (regioregular)
P3HT
CAS RN: 125321-66-6
Product Number: P2513

Performance of P3HT (regioregular) [P2513]-based OFETs

Fabrication method and evaluation of vacuum-deposited P3HT [P2513]



Table. OFETs Characteristics of P3HT (regioregular) [P2513]

Entry Fabrication Method Device Configuration SAM Treatment Annealing Temp.a (°C) Polarity μ (cm2 V−1 s−1) Vth (V) Ion/Ioff
Entry1 Fabrication MethodSpin-coating Device ConfigurationTCBG SAM TreatmentOTS Annealing Temp.a (°C)100 Polarityp μ (cm2 V−1 s−1)0.12 Vth (V)9.9 Ion/Ioff103
aPost-annealing temperature.

Figure. Transfer curves in the saturated region

Figure. Transfer curves in the saturated region


Experimental details

Fabrication and evaluation of spin-coated P3HT (regioregular) [P2513]-based OFETs

< Substrate >
  • OTS-treated Si/SiO2 (thickness of SiO2：300 nm)

< Self-Assembly Monolayer (SAM) Treatment >
  • n-Octyltrichlorosilane (OTS) [O0168]
    1. Piranha etching (H2SO4:H2O2=4:1, 80ºC, 2h)
    2. Ultrasonication (Deionized water, Acetone, IPA, 10 min each)
    3. Exposure to vapor (IPA, 3 min)
    4. UV/O3 treatment (1 h)
    5. Immersion in OTS solution (0.01 M toluene, 16 h, N2)
    6. Ultrasonication (Toluene, Acetone, IPA, 10 min each)

< Spin-Coating >
  • P3HT (regioregular) [P2513] 10 mg/ml, 1,2,4-Trichlorobenzene:Chloroform (2:98) mixed solvent
  • Spin-coating condition: 1500 RPM, 60 sec, N2

< Vacuum Deposition >
  • Deposition rate of Au: 0.2 Å/s (under a pressure of∼10−4 Pa)

< Post-Annealing Treatment >
  • Annealing condition: 100 ºC, 30 min, N2

< Device Configuration >
  • [n+-Si/SiO (300 nm) / P3HT (regioregular) [P2513] (100 nm) / Au (40 nm)]
  • Bottom-Contact Bottom-Gate Type (TCBG)
  • Channel Length: 50 μm
  • Channel width: 1.5 mm

< Evaluation Condition >
  • Under N2
  • Field-effect mobilities (μ) were determined from the transfer curves in the saturation regime using the following equation:
    ID = (W/2L) μ Ci (VG − Vth)2

TCI products used in this experiment

P2513 Poly(3-hexylthiophene-2,5-diyl) (regioregular)
O0168 n-Octyltrichlorosilane (OTS)

Page Top

Session Status
Your session will timeout in 10 minutes. You will be redirected to the HOME page after session timeout. Please click the button to continue session from the same page. minute. You will be redirected to the HOME page after session timeout. Please click the button to continue session from the same page.
Continue Operation
Your session has timed out. You will be redirected to the HOME page.
Close