text.skipToContent text.skipToNavigation

Maximum quantity allowed is 999

请选择数量

CAS RN: | 產品號碼: L0465

Live/Dead Cell Staining Kit [for Cell Staining]


纯度/分析方法:
別名
文件:
1KIT
NT$11,640
16   0   聯繫我們

* 以上價格已含運費關稅等但一些需要海運以及乾冰運輸的產品除外,詳情請與 當地經銷商 洽詢。
* TCI會時常優化儲存條件,儲存溫度請以在線目錄為準,敬請留意。


補充產品訊息:

Product Information

  • Components : Calcein-AM Solution (Ex/Em = 490 nm/515 nm), PI Solution (Ex/Em = 530 nm/620 nm)
  • Size : Calcein-AM Solution (1 mM) in DMSO50 µL×4 vials, PI Solution (1.5 mM) in Water600 µL×1 vial

Description

  • This product is a combination of Calcein-AM, a fluorescent dye for staining live cells, and PI (Propidium Iodide), a fluorescent dye for staining dead cells, allowing simultaneous staining of live and dead cells. It can be used to observe cells under a fluorescence microscope.

Direction for Use

[Staining Solution Preparation]

    1. Bring Calcein-AM solution and PI solution to room temperature.
    2. Add 1 μL Calcein-AM solution and 3 μL PI solution to 1mL PBS. This is the staining solution. At this time, the concentrations of Calcein-AM and PI are 1 μM and 4.5 μM, respectively.
  • Note: Staining conditions will vary depending on observation conditions such as cell type and concentration. Optimal conditions such as reagent concentration should be considered.
    Calcein-AM can be hydrolyzed by moisture, so replace the cap tightly after use and be careful not to absorb moisture.
    Prepared staining solutions should be used on the same day.
    PI is a suspected carcinogen and should be handled with caution.

[Determination of Optimal Staining Concentration]

  • Kill cells by treating with 0.1% saponin or 0.1-0.5% digitonin for 10 minutes or 70% methanol for 30 minutes.
    Stain dead cells with 0.1-10 μM PI solution to find a concentration that stains only the nuclei red without staining the cytoplasm.
    Stain dead cells with 0.1-10 μM Calcein-AM solution to find a concentration that does not stain the cytoplasm. Then confirm that live cells stain at this concentration. If staining is inadequate, increase the concentration.

[Cell Staining]

    1. For adherent cells, digest cells with cell scraper or trypsin-EDTA and collect by centrifugation (1000 rpm, 3 minutes). For suspended cells, collect cells by direct centrifugation (1000 rpm, 3 minutes).
    2. Centrifuge the cell suspension, remove the supernatant and add PBS. Thoroughly disperse the cells by pipetting or other means. Repeat washing with PBS and centrifugation 2-3 times. Cells should be washed prior to testing, as esterases present in serum containing medium may hydrolyze Calcein-AM resulting in increased background.
    3. After centrifugation, remove the supernatant and add the staining solution (adjust cell count to approximately 0.5 x105 - 10 x105 cells/mL).
    4. Incubate at 37 °C for 15 minutes.
    5. Place the stained cell solution on a slide, gently cover with a coverslip, and examine under a microscope.

Storage

Store at -20 °C. This product is photosensitive and should be protected from light.

產品號碼 L0465
外觀與形狀(20°C) Liquid
儲存條件 Frozen (-20°C)
應避免的情況 Heat Sensitive
產品規格
性質
GHS
信號詞 Warning
危險性說明 H227 : Combustible liquid.
防範說明 P501 : Dispose of contents/ container to an approved waste disposal plant.
P210 : Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
P280 : Wear protective gloves/ eye protection/ face protection.
P370 + P378 : In case of fire: Use dry sand, dry chemical or alcohol-resistant foam to extinguish.
P403 : Store in a well-ventilated place.
相關法規
運輸資料
HS編碼* 3822.19-000
*此H.S.編碼用於日本出口報關, 不適用於您所在國家或地區的進口申報
產品文件 (部分產品的分析圖譜無法提供,敬請諒解。)
SDS
請選擇語言。

請求的SDS不可用。

如需更多幫助,請聯繫我們

產品規格
檢驗報告(CoA)及其他文檔
請輸入批號 輸入的批號不正確

所搜尋批號的產品已停產,無相關文件。

示例 CoA
可下載CoA示例。注:該示例可能非最新批次的CoA。

目前沒有該產品的 CoA 示例。

分析圖譜
請輸入批號 輸入的批號不正確

很抱歉,您搜索的分析圖譜無法提供。

所搜尋批號的產品已停產,無相關文件。

其他文件

會話狀態
當前會話將在10分鐘後超時,並返回主頁。請點擊按鈕繼續瀏覽。分鐘後超時,並返回主頁。請點擊按鈕繼續瀏覽。

您的會話已超時,將返回至主頁。